Office (719) 362-0258

We're

Totally in Control

Products

Goto the Store

Here is a listing of current products. Please note that some of these products are still in development. Updated status of these items will be changed on this as well as the news page. Additional pages are available for the items with a hyperlink be sure to click on them.

IntelliVerter
(Ready for delivery)
Giving intelligence to the common inverter. A control to manage the inverter in a Recreational Vehicle allowing for automatic cycling of the inverter, which will extend the time required between battery charges. Works on inverters using a remote input requiring a maintained or momentary dry contact.

Pricing
See Store

BattStat
Ready for delivery
A device that connects to your RV house batteries. Once connected, it sends status remotely using bluetooth to your cellular phone or other device. No more reading stupid lights that really only tell you when you are about to have a problem. Gives a readout of battery voltage to your bluetooth device.

Pricing

$40.00 ea

BT Inverter Remote
(Now Available)
Got an inverter you want to control from a remote location? Don't want to route wires or cables? Want to avoid making holes in your car, truck, RV, or Boat? There is a solution...go wireless Bluetooth to your Android and control your inverter. The control unit mounts near the batteries, tie in two power leads, plug the RJ-11 jack from your inverter to the control box. No cutting holes, just drill a couple holes for the control unit. The control unit will report back to your cell phone showing the inverter status. You will be able to turn the unit off and on. It will even read your battery voltage. The control works with inverters that require a dry contact to operate. It can be configured to work with maintained or momentary contacts.

Pricing

$50.00

TinyDuino OLED/433mHZ RF Link Receiver/Prototype Shield
Now Available
A prototype shield for the TinyDuino providing availability to all pins. The board also contains a I2C OLED port connected to A4 & A5 pins; A 433mHz RF Link Receiver port connected to pin 9. See picture of application using this shield shown above. Stack spacing allows components to be mounted on both sides of the board. This board should be the top one on your stack. See all the Control House TinyDuino Shields. You can find a description of this card on YouTube at https://www.youtube.com/watch?v=jL38rMgq_Mg

Pricing
$6.50 ea bare board only
$8.50 ea assembled board
$23.00 ea assembled board with OLED and Receiver installed
$30.00 ea assembled with everything you need to connect to a TinyDuino processor

TinyDuino_Proto_1.00
(Now Available!)
A prototype shield for the TinyDuino providing availability to all pins and still allowing space for your development using through hole technology and .100 spacing. Stack spacing allows components te be mounted on both sides of the board. Picture coming. See all the Control House TinyDuino Shields.

Pricing
$6.00 ea bare board only
$8.00 ea assembled board
$15.00 ea assembled with everything you need to connect to a TinyDuino processor

TinyDuino OLED w Bluetooth 1.00
(Now Available!)
A board prepared with a I2C OLED port connected to A4 & A5 pins; A Bluetooth port connected to pins 0 & 1. The prototype area onboard for the TinyDuino provides availability to all pins. Limited by space required for the attached components. Stack spacing allows components te be mounted on both sides of the board. This board should be the top one on your stack. Picture coming. See all the Control House TinyDuino Shields.

Pricing
TBD

ProMini Stack System Base_1.00
(Now Available!)
A board prepared for the mounting of a Pro-Mini processor with pins tied to the shield system manufactured by Control House. All the shields shown on this site for the TinyDuino can be attached to this processor base unit. Picture coming. See all the Control House TinyDuino Shields.

Pricing
TBD

Programmer HC05_1.00
Now Available
Standalone batch programmer for HC-05 Bluetooth AT commands. Program  Bluetooth module with commands stored in the onboard Pro-Mini as prompted by an OLED display simply by pressing a button. Commands are entered on Pro-Mini using Arduino sketch pre-programmed. Or build your own sketch. Pins A4 & A5 are used to communicate with the OLED display, Pins 2 & 3 are used for the serial communication with the module. The HC-05 modules you use should be 5V tolerable but the RXD pin on the module is connected to the programmer through a voltage divider. The serial monitor can also be used to send individual commands to the module. External 5 volts must be supplied to the board either through the onboard terminal block or add a couple header pins and plug in if you wish. Did we mention that by adding headers you can mate this processor board with other shields being developed by Control House? Stack them below for a build it yourself expandable system.

Pricing
$40.00 complete unit less HC-05 module

Honda EU3000is Generator Mount
Now Available
Mount your Honda EU3000is on your RV rear bumper. This mount fits the generator like a glove! It fastens to your 4" square tube bumper using clamps. You are still able to lock the generator down to the mount and use the factory cover for protection while you travel.

Pricing
$175.00

 

Honda EU3000is Bluetooth Remote Start
In Test
Start and stop your generator from inside your camper! No need to add additional remotes. This one works with your Android device. It controls the choke and everything! It even allows control of the economy mode of the generator. An optional RF keychain remote is also available.

Pricing
Starting at $260.00

Picture coming!

IntelliVerter Momentary Contact Module
In Development
Module allows IntelliVerter to control inverters requiring a momentary contact closure. The module ties into the inverter using RJ11 port and connects to the IntelliVerter using the INV terminals.

Pricing
TBD

 

Welcome to the Control House Store

We're still working on this section of our site, thanks for your understanding if there are a few hiccups.


Back to the Top